User:Moggers87/Installing Opensuse

under construction.gif

Install OpenSUSE

Make sure you're in pvh mode

xen-shell> virtmode pvh

Boot rescue VM and log in

xen-shell> rescue

After a while you'll be presented with a login prompt. The password is auto-generated and should be printed a few lines above the prompt. Once you're logged in, become root:

user@rescue:~$ sudo -i
root@rescue:~#

Install required utilities into rescue VM

1. apt update
2. apt install rpm zypper curl btrfs-progs zstd parted

Set up partitions on disk

1. wipe existing block devices `for d in a b; do wipefs -a /dev/xvd${d}; done`
2. create partitions
   1. parted -s /dev/xvda mklabel gpt mkpart root btrfs 0% 100%
   2. parted -s /dev/xvda set 1 boot on
   3. parted -s /dev/xvdb mklabel gpt mkpart swap linux-swap 0% 100%
   4. mkfs.btrfs /dev/xvda1
   5. mkswap -L SWAP /dev/xvdb1
3. mkdir -vp /target && mount -v /dev/xvda1 /target

Copy in resolv.conf

1. cp -v /etc/resolv.conf /target/etc/

Set up Zypper repoes

1. set up repo files
   1. mkdir -p /target/etc/zypp/repos.d/
   2. cat <<-EOF > /target/etc/zypp/repos.d/repo-oss.repo

[repo-oss] name=Main Repository enabled=1 autorefresh=1 baseurl=http://download.opensuse.org/distribution/leap/\$releasever/repo/oss/ path=/ type=rpm-md keeppackages=0 EOF

cat <<-EOF > /target/etc/zypp/repos.d/repo-update.repo
[repo-update]
name=Main Update Repository
enabled=1
autorefresh=1
baseurl=http://download.opensuse.org/update/leap/\$releasever/oss
path=/
type=rpm-md
keeppackages=0
EOF

Install Zypper

1. run `zypper --releasever=15.3 -R /target install zypper`
   1. trust the key
   2. say yes to everything else

Mount chroot

mount -v --bind /dev /target/dev

mount -v --bind /dev /target/dev

mount -v -t proc procfs /target/proc

mount -v -t sysfs sysfs /target/sys

chroot /target /bin/bash

zypper --releasever=15.3 install openSUSE-release lsb grub2 dracut-tools wicked

cat > /etc/default/grub << EOF
# If you change this file, run 'grub2-mkconfig -o /boot/grub2/grub.cfg' afterwarrds to update
# /boot/grub2/grub.cfg.

GRUB_DEFAULT=saved
GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=10
GRUB_CMDLINE_LINUX_DEFAULT=""
GRUB_CMDLINE_LINUX="splash=silent mitigations=auto quiet"
GRUB_TERMINAL=console
GRUB_DISABLE_RECOVERY="true"
EOF

1. zypper --releasever=15.3 install kernel-default
2. grub2-mkconfig -o /boot/grub2/grub.cfg
3. networking:

cat > /etc/sysconfig/network/ifcfg-eth0 << EOF
TYPE="Ethernet"
PROXY_METHOD="none"
BROWSER_ONLY="no"
BOOTPROTO="none"
DEFROUTE="yes"
IPV4_FAILURE_FATAL="no"
IPV6INIT="yes"
IPV6_AUTOCONF="no"
IPV6_DEFROUTE="yes"
IPV6_FAILURE_FATAL="no"
IPV6_ADDR_GEN_MODE="stable-privacy"
NAME="eth0"
DEVICE="eth0"
ONBOOT="yes"
IPADDR=85.119.82.225
PREFIX=21
GATEWAY=85.119.80.1
IPV6ADDR=2001:ba8:1f1:f1d7::2/64
IPV6_DEFAULTGW=2001:ba8:1f1:f1d7::1
DNS1=85.119.80.232
DNS2=85.119.80.233
EOF

1. fstab

cat > /etc/fstab << EOF
/dev/xvda1  /   btrfs defaults,noatime 0 0
LABEL=SWAP swap swap  defaults         0 0
EOF

1. passwd root
2. openSUSE doesn't currently have selinux enabled by default, but if that changes in future you'll need to ask for a relabel *and* disable it for the first boot
3. exit chroot and dismount

exit
umount /target/sys
umount /target/proc
umount /target/dev
umount /target

1. halt